Owner guide · Hyundai of Goshen · Goshen, IN
How to Use the Hyundai Tire Mobility Kit
A nail in the tread does not have to end your drive. This guide follows the Tire Mobility Kit section of the 2027 Palisade owner's manual, text saved October 26, 2026; PDF link checked November 8, 2026: when the kit can help, when it cannot, the sealant steps in order, and how far and how fast you can drive afterward. The kit is fitted if equipped, and other Hyundai models can differ, so check the manual for your vehicle.
50 mphmaximum speed after sealing
120 mi.to reach a tire dealer
5-7 minutescompressor fill time
29 psiminimum pressure to drive
How do I use the Hyundai Tire Mobility Kit?
Park safely, shake the sealant bottle, connect it to the compressor and to the flat tire's valve, connect the kit's red and black cables to the jumper terminals in the engine fuse panel, and run the compressor for about 5-7 minutes with the engine on. Drive about 4-6 miles below 50 mph to spread the sealant, then set the tire to the recommended pressure. Drive no more than 120 miles and have the tire replaced.
What the Tire Mobility Kit is
Some Hyundai models come with a Tire Mobility Kit (if equipped) instead of relying only on a spare. In the 2027 Palisade owner's manual, the kit is a compressor and a sealant bottle. The manual says the compressor and sealing compound system effectively and comfortably seals most punctures in a passenger car tire caused by nails or similar objects, and reinflates the tire.
Once you are sure the tire is properly sealed, the manual says you can drive cautiously on it, up to 120 mi. (200 km) at a maximum speed of 50 mph (80 km/h), to reach a service station or tire dealer for tire replacement. The kit is not designed or intended as a permanent repair and is to be used for one tire only. Have the tire replaced by an authorized Hyundai dealer as soon as possible.
When not to use it
The manual lists several cases where the kit should not be used or may not work:
- Punctures in the tire wall (sidewall). Only punctured areas within the tread region of the tire can be sealed.
- Two or more flat tires. The sealant in the kit must be used for only one flat tire.
- A damaged tire and wheel, or a tire severely damaged by driving run flat or with insufficient air pressure.
- Tire damage larger than about 0.16 in. (4 mm), where the kit may not be effective.
- Ambient temperatures below -22 °F (-30 °C).
- Sealant that is past the expiration date on the sealant container.
- Motorcycles, bicycles or any other type of tires. The kit is for passenger car tires.
Do not remove foreign objects such as nails or screws that have penetrated the tire. If the tire cannot be made roadworthy with the kit, the manual says to contact an authorized Hyundai dealer.
How to use the Tire Mobility Kit, step by step
Park at the side of the road away from moving traffic and apply the parking brake, even on level ground. Detach the speed restriction label from the sealant bottle and place it where the driver will see it, such as on the steering wheel. Then follow the sequence in the 2027 Palisade owner's manual; the manual says to follow it strictly, or the sealant may escape under high pressure:
- Shake the sealant bottle.
- Connect the filling hose on the compressor to the sealant bottle. Keep the bottle upright so the filling hose is heading upwards.
- Unscrew the valve cap from the valve of the flat tire and screw the sealant bottle's filling hose securely onto the tire valve.
- Make sure the compressor is switched OFF.
- Open the hood and remove the engine compartment fuse box cover.
- Connect the RED cable to the + jumper terminal and then the BLACK cable to the - jumper terminal in the engine compartment fuse panel.
- With the engine ON, switch on the compressor and let it run for about 5-7 minutes to fill the sealant. Do not overinflate the tire, and stay away from it while filling.
- Switch off the compressor, detach the hoses from the sealant bottle connector and the tire valve, and return the kit to its storage location.
- Immediately drive about 4-6 mi. (7-10 km, or about 10 minutes) to spread the sealant evenly in the tire. Do not exceed 50 mph (80 km/h) and, if possible, do not go below 12 mph (20 km/h).
- Stop at a safe location, connect the compressor's filling hose directly to the tire valve, and adjust the tire to the recommended inflation pressure.
The manual warns not to drive if the tire pressure is below 29 psi (200 kPa), because sudden tire failure could cause a crash. If the pressure is not maintained, drive a second time and repeat the last steps. If you feel unusual vibration, ride disturbance or noise while driving, slow down, pull off safely, and call for roadside service or towing.
Tire Mobility Kit numbers at a glance
| Item | What the manual says |
|---|---|
| Driving after sealing | Up to 120 mi. (200 km), at a maximum of 50 mph (80 km/h), to reach a service station or tire dealer |
| Compressor fill time | About 5-7 minutes with the engine on |
| Compressor run limit | No more than 10 minutes at a time, or it may overheat |
| Distribute the sealant | Drive about 4-6 mi. (7-10 km, about 10 minutes), between 12 mph (20 km/h) and 50 mph (80 km/h) |
| Minimum pressure to drive | 29 psi (200 kPa) |
| Largest damage it may seal | About 0.16 in. (4 mm) |
| Lowest temperature for use | -22 °F (-30 °C) |
| Wheel nut torque when reinstalling | 79-94 lbf·ft (11-13 kgf·m) |
From the Tire Mobility Kit section of the 2027 Palisade owner's manual, text saved October 26, 2026; PDF link checked November 8, 2026. Equipment and figures can differ by model, so check the manual for your vehicle.
Safety and good to know
More points from the same manual:
Leave the engine running, outdoors only
Provided the vehicle is outdoors, leave it running while you use the compressor, or it may drain the battery. Never run the engine in a poorly ventilated area for long, because of carbon monoxide.
Disconnect black first
When disconnecting the kit, remove the BLACK - cable from the jumper terminal first, then the RED + cable, and watch for sparks.
Only need air?
If the tire only needs pressure, connect the compressor hose directly to the valve without the sealant. Switch the compressor on to add pressure, or press the button on the compressor to reduce it. The gauge may read high while the compressor runs, so switch it off for an accurate reading.
Sealant first aid
Keep sealant away from children, eyes and mouth. Wash skin contact with plenty of water, flush eyes for at least 15 minutes, and seek medical attention if irritation persists or sealant is swallowed.
After the repair
Sealant on the tire pressure sensor and wheel should be removed when the tire is replaced and the sensors are inspected. The manual says to have this done at an authorized Hyundai dealer.
Hyundai of Goshen service hours
| Days | Hours |
|---|---|
| Monday to Friday | 7:30 a.m.-5:30 p.m. |
| Saturday | 8 a.m.-3 p.m. |
From Hyundai of Goshen's website, November 8, 2026. The website lists Monday to Saturday service hours and none for Sunday. Holiday hours can differ.
Hyundai Tire Mobility Kit questions
How do you use a Hyundai Tire Mobility Kit?
Shake the sealant bottle, connect the compressor hose to the bottle and the bottle's filling hose to the tire valve, connect the RED cable to the + jumper terminal and the BLACK cable to the - jumper terminal in the engine fuse panel, and run the compressor for about 5-7 minutes with the engine on. Then drive about 4-6 miles to spread the sealant, stop, and set the tire to the recommended pressure.
How far can I drive after using the Tire Mobility Kit?
The manual says up to 120 mi. (200 km) at a maximum of 50 mph (80 km/h), to reach a service station or tire dealer for tire replacement.
Is the Tire Mobility Kit a permanent fix?
No. The manual says it is not designed or intended as a permanent repair, is for one tire only, and the tire should be replaced by an authorized Hyundai dealer as soon as possible.
Can the kit fix a sidewall puncture?
No. Only punctures within the tread region can be sealed. The manual warns that using the kit on a puncture in the tire wall can result in a crash due to tire failure.
Should I pull the nail out before using the sealant?
No. The manual says not to remove foreign objects such as nails or screws that have penetrated the tire.
Can I use the compressor just to add air?
Yes. Connect the compressor's filling hose directly to the tire valve and do not use the sealant. Do not run the compressor for more than 10 minutes at a time.
Does my Hyundai have a spare tire or a Tire Mobility Kit?
It depends on the model and trim. The manual lists the Tire Mobility Kit as equipment fitted if equipped, so check your vehicle's cargo area and its owner's manual.
Sealed a flat?
The kit is a temporary fix. Bring your Hyundai to Hyundai of Goshen at 3202 Elkhart Road in Goshen, IN for a tire replacement and a check of the tire pressure sensor, or schedule service online.
Sources
Steps, limits and warnings come from the 2027 Palisade owner's manual, text saved October 26, 2026; PDF link checked November 8, 2026. Other Hyundai models can differ, so the manual for your vehicle is the final word. Address and hours are from Hyundai of Goshen's own website. Image: Hyundai Motor America.
- 2027 Hyundai Palisade owner's manual (PDF): If You Have a Flat Tire (with Tire Mobility Kit); Notes on the safe use of the Tire Mobility Kit; Using the Tire Mobility Kit when a tire is flat; How to adjust tire pressure, Hyundai Motor America, text saved October 26, 2026; PDF link checked November 8, 2026
- Palisade (image), Hyundai Motor America, November 8, 2026
- Address and service hours (structured data), Hyundai of Goshen, November 8, 2026
- Hyundai service at Hyundai of Goshen, Hyundai of Goshen, November 8, 2026
